DREMEL 3D Support

Our 85-year old story is one that showcases our commitment to our customers through excellent customer support. From professional development training to grant writing assistance, we will help you and your teachers be successful.

You can register your Dremel 3D printer by following the instructions on our registration page.

We do not recommend you to print any object that will come in either direct or indirect contact with food.

Dremel's 3D printers will turn back on to an idle state after a power disruption. The previous print project will be cancelled automatically. If the print head is still hot, the fans will turn on to cool it down.

If your printer does not home smoothly, the wire bundle may be getting pinched between the gantry and the build platform resulting in y-axis belt slippage. Try repositioning the wire bundle to prevent it from getting pinched and homing should go smoothly.

Clean the Dremel 3D Printer's exterior with a lint free cloth. Clear the outer surfaces of any debris that is visible. To avoid damaging your Dremel 3D printer do not use water, chemicals or other cleaners on the printer. Always check to ensure the extruder nozzle is clear of debris using common needle nose pliers. Also be sure to change the build tape at regular intervals.

This is because the desiccant pack that comes with the filament developed a tear. This is common, and the "dirt" you see within the packaging is a form of salt that keeps the filament dry during storage. After the filament is opened, this can be safely thrown away in the garbage. Even though this contains salt, please refrain from eating it.

Please ensure that you are running the "unload" function, and that the extruder has heated to the appropriate temperature. If the filament is still difficult to remove, push down on the side mounted level to disengage the extruder's motor. Then gently pull the filament out of the extruder. Also, make sure that the nozzle is not clogged and that the extrusion head is properly heated. For further troubleshooting, please contact Dremel's customer service department for service information or visit the Support page on Dremel3D.com.

This may be the result of a build failure or a poorly constructed file. The building process may have been interrupted by the computer disconnecting, or by removing the SD card/USB flash drive during the building process. Run the Dremel Test Print to verify that your printer is working correctly, allowing the print to finish completely before disconnecting it.

Please ensure the extruder wire tube (tube with black mesh housing) moves freely and is located away from the build platform and guide rails. If caught on the build platform, the extruder will not return to home position and a loud noise may occur. In the event that extruder wire tube is caught on the build platform, power off the unit and reposition the wire tube above the build platform to allow it to travel freely.

It is possible that the motors are not running correctly or that the model file is corrupted. If you are using an SD card or USB flash drive, attempt the official Dremel Test Print through your computer software. If you are using the computer software, attempt to load the test print via SD card or USB flash drive. If you are still unable to move the extruder, check your printer for firmware updates by running the updater in the Dremel 3D software. If the steps above do not resolve the issue, please contact Dremel's customer service department for service information or visit the Support page on Dremel3D.com

You can unclog your extruder by using the unclog tool and following the steps in the instruction manual.

Make sure that the nozzle is not clogged and that the filament is properly inserted into the extrusion head. The most common reason for filament not loading correctly is a bad filament tip. Ensure the end of the filament has a clean break and does not contain any kinks or strings. It is recommended that you cut a small amount of filament off the tip to ensure a clean tip. Please also ensure that you are running the "load" function, and that the extruder has heated to the appropriate temperature. For further troubleshooting, please contact Dremel's customer service department for service information or visit the Support page on Dremel3D.com.

The extruder tip is scrapping the build platform because the build platform is not level and the extruder is too close. If this happens you should stop building and see instructions on leveling the build platform.

The extruder may have skipped off the track as a result of the build platform not being level or due to a buildup of excess filament around the extruder tip. The Dremel 3D printer did not detect this skip and is one step ahead of the extruder. If this happens you should stop building and see instructions on cleaning the extruder tip and leveling the build platform.

Please refer to the user manual and quick start guide for setup and building operations to ensure that your 3D Printer is connected and setup correctly. Also, it is recommended that you check to make sure your 3D Printer is using the most up-to-date software. For further troubleshooting, please contact Dremel's customer service department for service information or visit the Support page on Dremel3D.com

Yes, you can, majority of modeling software can export files to STL, which is the file type accepted by all Dremel-compatible Software.

You can use any CAD program to create the .stl of .obj file. However, you will need to use one of Dremel's compatible slicing softwares to convert these model files to buildable files.

3D models should be saved in STL or OBJ format in the CAD program used to create these files. You can then use your choice of Dremel 3D softwares to convert the files into buildable models.

Please contact Dremel's customer service department for service information or visit the Support page on Dremel3D.com

No, both of Dremel's 3D Printers are constructed with single extruder systems. This provides maximum reliability.

Please refer to the Products page to see the different versions and what is included.

3D printing is a method of creating objects through additive means. Many different forms of 3D printing exist today, but the Dremel 3D printers utilize Fused Filament Fabrication (FFF) to extrude layers of material on top of one another until an object is realized.

Storing your filament correctly extends the usefulness of the filament. Filament should always be stored in a cool, dry environment unexposed to changes in temperature or humidity. Always keep your filament inside the shrink-wrap plastic until you are ready to use it.

How long your filament lasts will depend on how often the 3D printer is used, and the quality/density at which objects are made. The lower the quality/density, the less filament required to build each object and the longer each roll of filament will last. Each Dremel filament roll will print continuously for roughly 24 hours.

Dremel filament is manufactured to provide the highest quality during operation and will help your Dremel 3D printer run smoothly. Using other manufacturers' filaments will void your warranty and may damage your Dremel 3D printer.

This pre-print activity allows the extruder to flush out any old filament that may not stick properly during your print. By purging this material, you are printing with filament at the optimal print temperatures, providing maximum hold with the first layer of the print.

Both build tapes will provide the same quality of build, the main difference between the build tapes is the durability and slight differences in object removal.

The black build tape will last up to 50 prints; the blue build tape will last up to 10 prints.

Supports are designed to be easy to remove and they should leave minimal marks on your print, however if you find some marks you can sand them with fine sanding paper.

You may have forgotten to enable supports in your slicing process. Please refer to tutorial guides for the respective slicing software you are using to ensure you have enabled supports.

Yes. You can pause an object to change filament using the touch screen. Please refer to the instruction manual for more information.

There are many reasons why objects may not stick to the build platform. You should first ensure that you have clean, debris free build tape and that it is not torn or ripped. Next, check that the build platform is level. These are the two most common causes for builds not sticking.

Objects sticking to the build platform is a good thing as they require a firm adhesion to the build platform to avoid slipping. This is to ensure that the object remains stable throughout building. See instruction manual for object removal instructions.

The Dremel 3D40 & 3D20 have a maximum resolution of 100 microns and a minimum resolution of 300 microns (0.10-0.30mm per layer). The higher the resolution, the smaller each layer and the better your object will look.

The time it takes to build a 3D object depends on the size and complexity of the model file. It also depends on the density you wish to build the object.

3D40: Maximum build volume is 10” x 6” x 6.7” (254mm x 154mm x 170mm).
3D20: Maximum build volume is 9” x 5.9” x 5.5” (230mm x 150mm x 140mm).

Build quality depends on a number of factors such as layer thickness and build environment. The Dremel printers (3D20 & 3D40) extrude filament into layers as thick as a sheet of paper or 100 microns (0.10mm) thick. The printers also have an active cooling fan which helps to evenly cool filament and reduce warping. They are designed to provide a fully enclosed build environment and gripped feet for stability. Lastly, an important factor is the quality of the filament used. Always use Dremel filament with Dremel's printers for the best quality.

Video Tutorials

How to remove excess filament from the extruder tip with wire clippers or scissors on the Dremel 3D Idea Builder.
Updating the firmware and software with the Dremel 3D Idea Builder.
Watch this video for information on what to do when the extruder is clogged in your Dremel 3D Idea Builder.
Get to know your Dremel 3D Idea Builder and the components of the printer with this product walk around.
Watch this video for helpful hints on how to prepare the Dremel 3D Idea Builder's build platform and how to get leveling just right.
Watch for information on how to remove imperfect filament to make installing easier with the Dremel 3D Idea Builder.
Learn how to install the filament into the guide tube for the Dremel 3D Idea Builder.
Watch the Idea Builder from the first step of building an object to removing a printed model from the build platform.
Watch how to update the firmware of your Dremel 3D40 Idea Builder. You can either easily update the firmware directly from the touch screen or do it manually by downloading the firmware from the Dremel 3D Website and loading it onto a blank USB flash drive.
Watch how to clean the extruder tip and unclog it in an unlikely case of an occurring extruder jam during filament loading or building. The Dremel 3D40 Idea Builder provides an easy and quick solution in order to continue with your 3D printing.
Learn about all the accessories that come with the Dremel 3D40 Idea Builder and how to get started with setting up your Idea Builder. Find more information on the Dremel 3D Idea Builder by visiting www.dremel3d.com.
Experience how to use Autodesk Print Studio for creating 3D printing models with Dremel 3D40 Idea Builder. Simply download the Print Studio software from www.dremel3d.com or install directly from the included USB flash drive, follow the steps shown in the video and get started with your 3D printing files.
Learn how to install filament for your Dremel 3D40 Idea Builder so that you can begin building your project instantly. Dremel offers PLA filament that has been specifically engineered for optimal printing in a wide variety of vibrant colors .
The Dremel 3D40 Idea Builder makes leveling the build platform easy. The Idea Builder provides a self-check on the platform to determine whether additional manual adjusting is required. The full color touch screen shows you once you are perfectly set up in order to ensure best quality 3D printing.
The Dremel 3D40 Idea Builder makes 3D printing easy! The full color touch screen lets you go from file to building effortlessly. Watch and learn how to make your model come to life.
Learn how to build a model from the Dremel 3D mobile app for the 3D40 Idea Builder. Watch the steps including installing the mobile app on your iOS or Android device, setting up the Wi-Fi connection to your printer, and starting your 3D printing project from the Dremel 3D app.